気泡なし！べっ甲風マーブルとお花のヘアクリップつくり方【秋のべっ甲カラー】UV-LEDレジン

気泡なし！べっ甲風マーブルとお花のヘアクリップつくり方【秋のべっ甲カラー】UV-LEDレジン

This is Comarin resin.
Sold out hair clip series.This time we will deliver tortoiseshell color.The
materials are here.Please pause and take a look.All
links are also listed in the summary section.This
time, the tortoiseshell color is
orange, brown, and black.・It can be made with 4 colors: brown and yellow.This
time, I will apply a thin coat to the hair clip, so I
will use a 1:1 ratio of color and coloring agent to make it quite dark.The
flowers used are mini daisies purchased at a crotcher shop.
These are the three osmanthus flowers I bought on the Lace Flower flea market
app.Autumn-colored flowers go well with tortoiseshell flowers, so please try making them with flowers you already have.Prepare the flowers.For the daisy flowers, make
air bubbles from the center
. A lot of will come out, so apply a thin layer of resin and let it harden.Remove the
broken petals and soak it in the resin to remove any air bubbles.Cut
the lace flowers into sizes that are easy to use.The
osmanthus flowers are on the front. I want the petals and stems to be separated and used.Pour
the resin over the area where the flowers will be placed and spread it with a brush.Place the
mini daisies facing downwards and
arrange the other flowers in a well-balanced manner.As for
the osmanthus, once the resin is applied, it will spread all over the place. Be careful when handling it as it will crumble easily. Let
it irradiate for 1 minute. Pour
the resin all over the mold.
Leave it for about 5 to 10 minutes to release air bubbles from the gaps between the flowers. Trace
with a toning stick to release air bubbles and use a brush to release the air bubbles. Remove them one by one.There
are also air bubbles in the corners of the mold, so trace them all to remove them.Remove the
resin liquid on the edges of the mold and
irradiate it for 2 minutes.Irradiate
the back side for 2 minutes to harden it thoroughly.Remove it
from the mold.It
looks like this Now,
use scissors to cut the part where the flower is sticking out.
I am using Tamiya craft scissors
. The inside of the cut flower is not hardened, so I shine it with a light for 1 minute. I use a file to
make the back side flat. Be careful not to scrape the resin part.
After sanding, spray with water and wipe off the powder.
Since the flower has a cross section, avoid washing it completely under tap water. Remove
all the powder by buffing it with tape. There
was one part that was covered, so I fixed it by adding resin solution.There was an
air bubble coming out of the osmanthus, so I made a hole and filled it with resin solution.From
here, I will attach the hair clip
fittings.Others In the video, I sometimes attach it with adhesive, but
this time I would like to attach it with resin liquid because the light will hit the metal fittings from the surface.
Apply resin liquid to the upper part, and apply a
thin layer to the lower part because it tends to stick out. Set it aside.
Once you place the resin on the metal fittings, hold it firmly with your hands and irradiate for 1 minute. Be
careful as it moves easily
. Next, fill the sides of the metal fittings with resin liquid.
This process can only be done with a smooth type of resin. Please be careful.
Check if there are any air bubbles from the surface and remove them with tweezers. I
think this method is the best way to finish the metal fittings at the moment.
Irradiate for 1 minute. There are
also opposites. Do the same thing.Next
, apply the coating agent to the sides.Place it
with clothespins so it doesn’t get on your hands and spread it all around at once.There
is a video that explains the coating in detail, so if you would like, please watch it in the summary section.Irradiate for
2 minutes. Paint
the back side. Pour the resin solution on large areas, but be careful not to let it drip to the sides. For the remaining areas, use the
tip of the toning stick to spread the resin solution.
Be careful not to let it drip from the sides. Once
everything is coated, irradiate for 2 minutes.Cut
the ball chain that will be attached to the border of the color.Spread a
thin layer of resin where the ball chain will be attached, place
the ball chain, and adjust the position.Irradiate
for 1
minute.Ball Apply clear resin to the bottom of the chain to create a wall to prevent the color resin from flowing.
Expose it for 1 minute.
Apply the tortoiseshell style color using the 4 colors you created at the beginning.
It’s surprisingly easy to do and uses 4 colors. It’s like applying it randomly.
Using the tip of the brush, lightly blend the boundaries of the color and apply more and more color.
Once it’s spread out to a certain extent, let it harden once and then apply another coat.
Personally, I think two coats gives the best three-dimensional effect. I think it will give a beautiful finish.I
irradiate it for 2 minutes.When
I was painting the color, I noticed air bubbles on the side, so I fixed it here.Next, I applied
clear resin to the areas other than the color resin, and
the whole area Make sure the height is flat.
Spread it thoroughly to the edges and irradiate for 1 minute.
If it’s flat when viewed from the side, it’s OK.
If there are any dents, fill them in.
Finally, use high viscosity resin. Make the surface plump.
To prevent it from dripping, I pour a small amount of resin solution and spread it with a brush at first, but I haven’t
applied it yet around the holes where it tends to drip.
Once I spread it, it takes about 5 to 10 minutes to remove air bubbles. Leave it alone.
Small air bubbles will float up, so remove them and spread it over the whole area.
Look from various angles to make sure there are no unpainted areas. Add
little by little to the areas where there is not enough resin.
This part where it is most prone to dripping should be last. I painted it on the surface
and cured it, but to prevent
side sagging, I used Daiso’s 6W LED light to temporarily cure it.I have posted
a video that explains in detail about side sagging in the summary column.Finally,
I usually do
This is a video of the
sold out hair clip series autumn tortoiseshell color.Thank
you for watching this far ♪

ヘアクリップは研究を重ね作り方をアップデートしています
最新版はこちら ⇒ https://youtu.be/YpQXxllUZ6A

参考にして作ったものは販売ＯＫです🌟
秋が来ますね～！今回は意外と簡単でデザインにも合わせやすいべっ甲カラーの作り方です♪ヘアクリップ以外でも使えるのでぜひ作ってみてください💖

※硬化時間はライトやレジン液によって変わります
※レジンをする時はマスクと手袋着用を推奨しています

【使用した材料一覧】

■作家のためのレジン低粘度（超さらさらモールド向け）
https://shop.croccha.com/products/list?category_id=505

■作家のためのレジン高粘度（表面ぷっくりのみこちらを使用）
https://shop.croccha.com/products/detail/7728

■作家のためのレジン着色剤（全12色）
https://shop.croccha.com/products/detail/8094

■作家のためのレジンコーティング
https://shop.croccha.com/products/detail/8023

■ヘアクリップモールド
https://shop.croccha.com/products/detail/7802

■ヘアクリップ金具
https://shop.croccha.com/products/detail/7738

■ミニデイジー
https://shop.croccha.com/products/detail/8526

■レースフラワー
https://shop.croccha.com/products/detail/7737

■ボールチェーン
https://shop.croccha.com/products/detail/7909

■調色パレット
https://shop.croccha.com/products/detail/6473

■シリコンブラシ
https://shop.croccha.com/products/detail/7641

■調色棒
https://shop.croccha.com/products/detail/7875

■ピンセット
https://shop.croccha.com/products/detail/8097

■UV-LEDライト
https://shop.croccha.com/products/detail/8093

■タミヤ クラフトハサミ

他知りたいものがありましたらコメントください♪

【基礎と細かいコツ＆技を学びたい人におすすめのシリーズ】

①⇒【モールド編】

②⇒【サイドコーティング編】

③⇒【表面ぷっくり編】

★レジンつくり方動画再生リスト

★作家のためのレジン(すべての作品で使用)
https://shop.croccha.com/products/list?category_id=505

★crocchashop
https://shop.croccha.com

✼••┈┈••✼••┈┈••✼••┈┈••✼••┈┈••✼

【ホームページ】
https://comarimade.jimdofree.com/

【Instagram】メインで更新してます
https://www.instagram.com/comarimade/

【Twitter】写真展示がメインです
Tweets by comarimade

【tiktok】たまにvlogも載せてます

@comarimade

✼••┈┈••✼••┈┈••✼••┈┈••✼••┈┈••✼

【BGM】さりいさん
https://www.youtube.com/@sari_bgm